11 Oct 08 Linux on a Mikrotik 532a, Part 4 – Customization, Debian Scripts, Shaping, Firewall, NAT, picoLCD

Follow On From: 05 Oct 08 APNIC Box – Linux on a Mikrotik 532a, Part 3 – Installing Debian, Prebuilt Disk Image

Following on from the previous article, I’ve written some scripts which you’ll find in the /root/scripts/ directory of the prebuilt image. I’ve attached and commented them here, as they could also be useful elsewhere.

bridge.sh #For setting up a simple bridge
(more…)

Tags: 532a, APNIC Box, bandwidth management, bandwidth rate, bridge, cbq, ifconfig, iproute2, iptables, lcd, Linux, picolcd, qdisc, routerboard, routerboard 532a, shaping, tc, time, usblcd, usleep

05 Oct 08 APNIC Box – Linux on a Mikrotik 532a, Part 3 – Installing Debian, Prebuilt Disk Image

Follow on from 01 Oct 08 APNIC Box – Linux on a Mikrotik 532a, Part 2

The device runs a 2.4.30 kernel on a debian woody (mipsel) environment. If anyone can contribute anything for 2.6.x and debian etch, that would be great.

In this part, I’m going to provide a download link to a prebuilt image which you can write directly onto your own CF card with dd or similar tool. I’m also going to provide a step by step to installing debian yourself without my prebuilt disk image.

Prebuilt image is here:

The prebuilt image also contains a number of scripts and tools that I’ll comment on and come to in later parts.

Now installation instructions:
(more…)

Tags: 532a, apnicbox, apt-get, atftpd, CF, compile, cross compile, Custom Kernel, dd, debian, dhcpd, dhcpd.conf installer, forward, initrd, initrd.gz, iptables, ip_forward, kernel, Linux, linuxrc, masquerade, mikrotik, mipsel, mkfs, mknod, mount, partition, prebuild image, routerboard, routerboard 532a, scripts, sed, tftpd, vmlinux, wget

01 Oct 08 APNIC Box – Linux on a Mikrotik 532a, Part 2 – Hardware Modifications

Follow on from 01 Oct 08 APNIC Box – Linux on a Mikrotik 532a, Part 1

Custom Hardware Modifications

Here’s a labelled image of the inside of the device. You can also look towards the bottom left of the image for my simple solder modifications. Enlarge the image to see the labels.

1. External 2.4GHz/5GHz antenna. Same on opposite side.
2. 5V solder point
3. 5V connector for miniPCI USB card
4. 2x 2USB Headers. 1 Header in use providing 2x USB interfaces, one to regular host connector for mass storage or other usb connection. Other port for picoLCD on top
5. 512MB CF card
6. miniPCI USB controller

On the underside of the board there is a single miniPCI socket which houses an Atheros 5212 802.11a/b/g miniPCI card. It has two antenna outputs which run under the board and two the two external antennae. I haven’t taken a picture of this but if anyone really wants to see it, I will power down the device, get a picture of it and post it here.

(more…)

Tags: 2.4ghz, 532a, 5ghz, 802.11, antenna, APNIC, APNIC Box, atheros 5212, Linux, mikrotik, minipci, minipci usb, picolcd, routerboard, routerboard 532a, solder, soldering, usb interfaces, usb ports

15 Sep 08 Using picolcd on linux, lcdproc, routerboard, liblcdusb

I’ve posted previously about my embedded device and picolcd. I wanted to put some thoughts down about using picolcd.

The easiest way to drive your picolcd is with lcdproc I’ve found. The device doesn’t require any special drivers which is great, as long as you have USB support working you’re fine. Make sure uhci-hcd and usbcore are loaded, you should be able to use ehci-hcd as well as it supports USB 1.1 and 2.0 but I haven’t tested that.

Use lsusb to make sure that the device is shown and recognised. If you see:

    Bus 002 Device 003: ID 04d8:0002 Microchip Technology, Inc.

then great. Your device is connected, working and your machine supports USB.
(more…)

Tags: drivers, ehci-hcd, embedded, lcdproc, libhid, liblcdusb, libusb, lsusb, pico lcd, picolcd, picolcd on linux, routerboard, uhci-hcd, usb, usbcore